Steam turbine generator · NorthRiver Midstream
3.5 MW steam turbine generator engineering, McMahon Gas Plant
Engineering for a 3.5 MW Triveni steam turbine generator package at NorthRiver Midstream's McMahon Gas Plant near Taylor, BC, working alongside Triveni Turbine and the owner's engineer.
Our scope covered 30% design (3D model, pipe stress and skid analysis, valve and component datasheets, EIC including PLC programming, P&IDs, PFD, line list, single line diagram, I/O list and control narrative), the RFQ package and technical bid evaluation for package fabrication, MCC procurement support, HAZOP attendance, and BC P.Eng. stamping of the issued-for-construction documents.
- Client
- NorthRiver Midstream
- Site
- McMahon Gas Plant, Taylor BC
- Equipment
- 3.5 MW Triveni steam turbine generator
- Scope
- Engineering, procurement support, HAZOP, P.Eng. stamping
Steam turbines
Steam turbine generator · CSV Midstream
3.1 MW back-pressure steam turbine generator, Albright Gas Plant
Supply of a 3.1 MW back-pressure steam turbine generator for CSV Midstream's Albright Gas Plant in northwest Alberta, recovering power from 55,000 kg/h of process steam.
The Howden CBA7 package takes steam at 4,400 kPa(g) and 257 °C and exhausts at 450 kPa(g) back to the plant, producing about 3 MW at the generator terminals. It included a Woodward 505 governor, DECS-250 excitation control, closed-loop cooling, an air-conditioned enclosure, utility-grade generator protection and power export limiting, with CSA certification.
- Client
- CSV Midstream (CSV Albright LP)
- Output
- 3.1 MW at the coupling
- Steam flow
- 55,000 kg/h
- Delivered
- 2024
Steam turbines
Power plant relocation · in progress
10.5 MW Waukesha power plant relocation, Washington to Alberta
Decommissioning and dismantling a multi-engine Waukesha gas engine power plant in Washington State, then relocating, retrofitting and reinstalling it at an existing oil and gas site in northern Alberta.
We are derating the plant for altitude, handling the site layout, noise assessment and permitting, and retrofitting the units as part of the 25 MW of reciprocating engine generation we currently have in production.
- Capacity
- 10.5 MW nameplate
- Engines
- Waukesha gas engine generators
- Scope
- Decommissioning, relocation, retrofit, permitting
- Status
- In progress, 2026
Power generation capabilities
Engine generators · repackaging
Waukesha L7042 generator sets: purchase, import and repackaging
Two used Waukesha VHP L7042 generator sets bought in the United States, imported to Canada (including the Environment and Climate Change Canada emissions declaration) and craned into our Calgary shop.
The original packages were poorly designed, so we are repackaging both units on new generator skids we designed and fabricated, refurbishing the engines and preparing them for deployment at an Alberta power facility.
- Engines
- 2 × Waukesha L7042GU / L7042GL
- Output
- 700 kW and 650 kW, 480 V
- Scope
- Purchase, import, skid design, repackaging, refurbishment
- Status
- In the shop, 2026
Power generation capabilities
Engine generators · new packages
Two Caterpillar G399 generator packages
Two Caterpillar G399 gas engine generator sets packaged for power generation, with an off-skid borescope inspection confirming good bores, valves and crosshatch before commissioning.
The Cat sensor set from these units became our standard for every project, so parts and controls are interchangeable across the fleet.
- Engines
- 2 × Caterpillar G399
- Scope
- Inspection, packaging, controls
- Status
- 2023–2024
New OEM gas engine packages
Engine generators · controls retrofit
MWM TBG620 V16 repackage and controls retrofit
Repackaging of an MWM (Deutz) TBG620 V16 gas engine generator whose original engine controller was obsolete and could no longer be configured.
We rewired the engine to simple standard sensors, terminated it on relay blocks under a Deep Sea controller with PLC permissives, fitted MIC4 ignition, detonation sensing, AFR control and a new throttle actuator, and converted the fuel system to natural gas with a new regulator and scrubber.
- Engine
- MWM / Deutz TBG620 V16
- Scope
- Repackage, rewiring, controls, ignition, AFR, fuel conversion
- Status
- 2023–2025
Engine retrofit & refurbishment
Engine generators · rebuilds and retrofits
MWM TCG 2016 V16 engine rebuilds and controls retrofits
Full rebuilds of several MWM TCG 2016 V16 gas engine generator sets, with overhaul parts and gasket sets sourced from MWM specialists in Europe.
Each unit gets a controls retrofit: Motortech MIC4 ignition with base timing and pickup index measured on the engine, new sensors and wiring, and our own control panels and remote monitoring.
- Engines
- MWM TCG 2016 V16 (several units)
- Scope
- Full engine rebuild, ignition and controls retrofit
- Status
- 2025–2026, more units in progress
Engine retrofit & refurbishment
Engine generators · rebuild
1.3 MW Cummins QSK60 generator set rebuild
An ex-rental 1,300 kW Cummins QSK60 generator set at the end of its rated engine hours, sourced in Texas, trucked to our Calgary shop and scheduled for a full rebuild before it goes back into service.
- Engine
- Cummins QSK60
- Output
- 1,300 kW, 480 V
- Scope
- Sourcing, transport, engine rebuild
- Status
- In the shop, 2026
Engine retrofit & refurbishment
Engine generators · new packages
New 1 MW generator set packages
New 1,000 kW engine generator set packages: skid design, with alternators, breakers, radiators and skid steel sourced for the first packages and a second batch of engines on order.
- Output
- 1,000 kW per package
- Scope
- Skid design, packaging, procurement
- Status
- In fabrication, 2026
New OEM gas engine packages
Engine generators · fleet assessment
Fleet assessment: 11 GE Jenbacher JGS 320 generator sets
Condition assessment of a fleet of 11 GE Jenbacher JGS 320 gas engine generator sets, about 15 MW in total, to decide which units to rebuild, which to give zero-hour overhauls and which to use for parts.
- Engines
- 11 × Jenbacher JGS 320 GS
- Capacity
- About 15 MW
- Location
- Wyoming, USA
- Scope
- Condition assessment, rebuild options
Engine retrofit & refurbishment
Solar Saturn gas turbine generator
Gas turbine generator · Solar Saturn
800 kW Solar Saturn gas turbine generator: inspection and commissioning
Return to service of an 800 kW Solar Saturn gas turbine generator set in Calgary: internal borescope inspection of the turbine, inspection and review of the generator, and startup and commissioning with our Calgary millwright partner.
- Turbine
- Solar Saturn
- Output
- 800 kW
- Scope
- Borescope inspection, generator review, startup and commissioning
- Location
- Calgary, AB
Power generation capabilities
Cogeneration · Capstone microturbines
Microturbine cogeneration from 25 kW to 200 kW
Combined heat and power systems built around Capstone microturbines for greenhouses, commercial buildings, manufacturing and gas plants.
Projects include a Capstone C30 for a greenhouse, complete with automation systems; a Capstone C30 for a factory in Calgary; a 25 kW unit for Bow Valley Credit Union; a 100 kW system on order; and 200 kW units for gas plants.
- Greenhouse
- Capstone C30 with automation
- Factory, Calgary
- Capstone C30
- Bow Valley Credit Union
- 25 kW
- On order
- 100 kW
- Gas plants
- 200 kW units
Cogeneration
